Sending a drawing to a tool shop is a disclosure, and it happens before any commercial relationship exists. The document leaves the buyer's control at the first email, and everything that follows is about limiting what that means.

This page describes the four nodes a drawing passes through, the controls available at each, the minimum information a tool review actually needs, and the eight points an NDA should cover.

A drawing passes through four nodes: sending, review, manufacture and archive. Each one has a different exposure and a different control, and the control has to be in place before the node, not after.

The practical answer to the disclosure problem is the minimal-information principle: send a tool view with the features and tolerances the tool must reproduce, agree the terms, and send the full drawing only when the review has succeeded.

The commercial structure that usually accompanies this is covered in trial run terms for custom cutting tools. This page covers the document itself.

The four nodes of a drawing's life

Sending. The drawing leaves the buyer's system. Exposure begins here: the recipient list, the mailbox, the storage location and whether the file is forwarded. Most disclosures that matter happen at this node, before anyone has signed anything.

Review. An engineer reads the drawing to decide whether the tool can be made. At this node the drawing is seen by people the buyer has never met, and often stored in a system the buyer cannot see.

Manufacture. The shop floor uses the drawing, or a derived tool drawing, to grind and inspect. Exposure here is different: the drawing becomes a working document with prints and setup sheets around it.

Archive. The drawing is retained, for quality records, for reorders, or by default. Retention is the node most often left unnegotiated, and it decides how long the exposure lasts.

The four nodes are sequential but not equally controllable. Sending is fully within the buyer's control; review and manufacture are within the supplier's; archive is usually governed by the supplier's quality system unless the agreement says otherwise.

How we work. The drawing you send is treated as the reference, not as the manufacturing document. We produce the production drawings from it and send them back to you for confirmation before the tool is made.

The revision you confirm is the revision that gets ground. Where something in the reference drawing is ambiguous, the question is raised at that confirmation step rather than resolved on the shop floor.

Controls available at each node

Each node has a control that is cheap to apply and expensive to skip.

NodeExposureControl
SendingForwarding, wrong recipient, uncontrolled mailboxNamed recipients, a single channel, and an NDA signed before the first file is sent
ReviewWider internal distribution than expectedA stated review scope: who may see it, whether a derived tool drawing is permitted, and whether subcontractors are excluded
ManufacturePrints, setup sheets, shop floor accessVersion control and marking; the manufactured article is traceable to one revision
ArchiveIndefinite retention, reorders quoting an old revisionAn agreed retention period, a return or destruction clause, and a reorder rule tied to the approved revision

The controls that cost nothing are the ones most often missing: a named recipient list, a single channel, and a statement of who may see the drawing internally.

Version control is a control as well as a quality measure. A drawing that exists in three revisions at a supplier is three exposures, and the one that gets manufactured is not always the one that was approved.

Marking each issue with a revision that the buyer can trace is therefore part of the protection, not part of the paperwork.

When a reorder is placed, the revision quoted is the revision that should be manufactured, and a supplier who cannot show which revision it holds cannot show which drawing it is protecting.

The minimal-information principle

A tool review does not need the part. It needs the feature the tool will cut, the tolerances it must hold, the material it will cut, and the machine it will run on.

That is a short list, and it can be expressed without the part number, the assembly, the customer or the programme.

A bore with its diameter, tolerance, length, pre-hole condition and material is enough to quote a reamer. The rest of the drawing adds context for the buyer, not capability for the supplier.

The sequence that follows from this is: send the tool view, get the feasibility and the price, agree the terms, then send the full drawing. The full drawing arrives when there is an agreement to protect it, not before.

Two practical notes. First, the tool view should still be dimensionally correct, because an approximate view produces an approximate quotation.

Second, the tool view should be marked as a tool view, so that the supplier does not assume it is the complete requirement and quote against a partial specification.

The fields a tool view needs are the same ones a complete drawing needs, and they are set out in how to call out a reamed bore on a drawing.

Eight NDA points

An NDA is only as useful as its definitions. These eight points decide whether it covers the disclosure that actually happens.

PointWhy it belongs in the agreement
Definition of confidential informationWithout it, a drawing may be argued to be a generic engineering document rather than confidential information
Direction: one-way or mutualA one-way NDA protects the buyer only; a mutual one also covers what the supplier discloses about its process
DurationTrade-secret obligations usually need a longer term than commercial confidentiality, and the two are often given the same period by mistake
Return or destructionDefines what happens to the drawing at the end, including copies in email and in quality records
ExclusionsPublicly known information and independently developed information are normally excluded; the wording decides how narrow the exclusion is
Subcontracting limitGrinding, coating and heat treatment are often subcontracted; without this point the drawing travels further than the buyer expects
RemediesStates what happens on breach, and whether injunctive relief is available
Governing law and forumDecides where a dispute is heard, which in cross-border work is often more consequential than the remedy clause

The subcontracting point is the one buyers most often omit and most often need. A tool shop that sends blanks out for coating has disclosed the drawing to a third party, and the NDA should say whether that is permitted and on what terms.

The duration point matters for the same reason. A two-year confidentiality term is adequate for a price list and inadequate for a drawing that describes a product still in production five years later.

Questions to ask before sending

Five questions settle most of the exposure before any file moves.

Who will see the drawing internally? The answer should be a role list, not "our engineering team".

Is any process subcontracted? Coating, heat treatment and sometimes grinding. If the answer is yes, the NDA has to cover it, or the process has to be excluded from the quotation.

Where is the drawing stored, and for how long? A retention period tied to the quality system is normal; an indefinite one should be negotiated.

Is a derived tool drawing permitted? Most suppliers will make one. Whether it may leave the supplier's control, and whether it becomes the buyer's property, is a separate question.

What happens at the end of the relationship? Return, destruction, or retention under a quality obligation. The answer should be in writing.

These questions are ordinary commercial diligence, not an accusation. A supplier that cannot answer them is a supplier whose document handling the buyer cannot describe.

What a supplier can and cannot commit to

Some commitments are structural and some depend on the supplier's own procedures and on the law that applies.

Structural commitments a tool supplier can normally make are: an NDA before the drawing is sent, a stated review scope, use of the drawing only for evaluation and manufacture of the ordered tool, and a return or destruction arrangement at the end.

Commitments that depend on the specific company, its quality system and its jurisdiction include the retention period, the treatment of subcontractors, the remedies available and the governing law. These are the points to confirm in the agreement rather than assume from a website.

Absolute assurances are not a substitute for a clause. A statement that information will never be disclosed is not enforceable in the way a defined obligation with a remedy is, and it does not answer the questions above.

Where the buyer's own customer requires flow-down obligations, those should be stated at the start, because they may change whether the tool can be subcontracted at all.

The programme structure for distributor and private-label work is described on the distributor cutting tool program and private label cutting tools pages.

To start with a tool view rather than a full drawing, send the feature through the custom cutting tool RFQ. What happens after the review, including the lead time and the minimum quantity, is covered in lead time and MOQ for custom cutting tools; for an NDA request, use the contact page.

Drawing transfer happens between the RFQ and the quotation, and the terms around it depend on what those two gates already fixed. The full sequence is in the procurement frame that governs drawing transfer.

What published sources say about this

These pages support the tolerance definitions and the documentary logic referenced above. Each is cited for what it states, under its own conditions.

  • Dimensioning and Tolerancing (ASME Y14.5): what makes a drawing a complete specification, which is also what makes a tool view a usable substitute for review.
  • What is a measurement system? (NIST/SEMATECH e-Handbook): the components of measurement variation, relevant when a tool view carries the tolerance that will later be judged.
  • What is Process Capability? (NIST/SEMATECH e-Handbook): process spread against specification, the basis for the acceptance data a drawing review will eventually require.
  • Reamers, machine reamers (toolmaker technical overview): reamer construction, which is what a supplier reviews a drawing against.
  • Reaming and fine boring (toolmaker competence page): the finishing families, used here to show why a review needs the tolerance and the pre-hole rather than the assembly.
  • Tools for fine machining bores (toolmaker interview): single-blade constructions and their handling requirements, which is the kind of detail a tool view can convey without the part drawing.
  • What are control charts? (NIST/SEMATECH e-Handbook): the time-ordered record, which is also the form in which a supplier's quality archive retains a drawing's manufacturing history.

Outbound references are listed because the reasoning depends on them, not as endorsements. The clauses described here are drafting points for a legal agreement; the text of any agreement is confirmed with the parties concerned.

Frequently asked questions

Should an NDA be signed before a drawing is sent?

Yes for a custom tool, because the drawing is the disclosure and it cannot be recalled once sent.

For a standard catalogue item the drawing may add nothing, and the NDA question does not arise in the same way.

Can a tool view replace the full drawing for a quotation?

For a quotation, often yes: the feature, tolerance, material, pre-hole and machine are what decide feasibility and price.

For manufacture, no. The full drawing is needed once the order is placed, and it should be sent at that point.

What is the most overlooked NDA point?

The subcontracting limit. Coating and heat treatment are frequently subcontracted, and a drawing can travel to a third party without the buyer knowing.

If the process is subcontracted and the NDA does not cover it, the disclosure has happened outside the agreement.

How long should confidentiality last?

Long enough to cover the product's production life, not just the order.

A short term is adequate for pricing and inadequate for a drawing that describes a part still in production years later.

Does a supplier keep drawings after the order ends?

Usually for a period set by its quality system, so that a reorder matches the approved revision.

Whether that period is defined, and what happens at the end of it, is a clause rather than a default.

Author: Kevin Zeng, Operations Director, HENTRY

Engineering review: Jiack Liu, Engineering Director

Updated 14 November 2026: first publication. Scope: the four nodes of a drawing's life, the controls at each node, the minimal-information principle, the eight NDA points and the five pre-send questions. The clauses are drafting points; agreement text is confirmed between the parties.